Skip to content

VideRime Online Learning

Search for:

Home
GK/GA MCQs
Questions?
- Ask Question
- Questions
Direct Links
Submit Article
Contact Us
Membership Registration
Login
Signup Now

Home
GK/GA MCQs
Questions?
- Ask Question
- Questions
Direct Links
Submit Article
Contact Us
Membership Registration
Login
Signup Now

Automobile Engineering MCQs
0

Automobile Engineering Practice Set-1

May 2, 2021

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

Show paginator

Hide paginator

33%

Page 1 of 3

1. The characteristic that is enhanced by the honing of cylinder sleeves inner surface is

Resistance to wear

None of these

Cooling efficiency

Lubrication performance

2. The painting of automobiles is done to

Improve its external appearance

All of these

Prevent rust from growing on the body

Retain the characteristics of steel for long

3. The crankshaft of a typical inline four cylinder engine has ________ balance weights.

8

12

4

16

4. The cetane number of a Diesel fuel is a measure of

Delay period

Viscosity

Ignition quality

Volatility

5. When the brake pedal free play is less than the specified value, then the

Brake drags

Brake fades

Antilock braking system malfunctions

Vapour locking occurs in the brake lines

6. The auto ignition in a spark ignition engine means

Automatic ignition of the charge at the end of compression

Ignition induced to supplement the process of normal combustion

Ignition of the charge before the passage of flame front

Ignition induced by the passage of a spark

7. The drive-shafts are connected to the differential and wheel hubs through universal joints because the universal joints

Compensate for variations in the relative positions of the differential and the wheels which result from bumpy road surfaces or other similar driving conditions.

Absorb any difference in speed between the left and right wheels when the vehicle is turning

None of the above

Absorb the vibrations transferred from the surface of the road

8. The vehicle ride will be comfortable if

Unsprung mass is kept minimum

All of these

Vehicle mass is kept minimum

Sprang mass is kept minimum

9. The calorific value of petrol is about

39.4-42.5 MJ/kg

42.7-43.5 MJ/kg

45.5-47 MJ/kg

36.5-38.5 MJ/kg

10. The brake warning light warns the driver of

Water in the master cylinder

Power brake failure

Air in the hydraulic system

Failure of the primary or secondary circuit of hydraulic system

Page 2 of 3

11. The path taken by intake air is

Air cleaner carburettor (or throttle body) intake manifold intake ports cylinders

Air cleaner carburettor (or throttle body) intake ports intake manifold cylinders

Carburettor (or throttle body) air cleaner intake manifold intake ports cylinders

Air cleaner intake manifold carburettor (or throttle body) intake ports cylinders

12. It is necessary to maintain the valve clearances as they

Allow for lengthening of the valves owing to the heat of combustion

Increase the speed at which the valves move up and down

Make the crankshaft turn smoothly

Reduce the resistance to sliding that occurs between the cam and the tappet

13. In petrol engines, during suction stroke, _________ is drawn in the cylinder

Only fuel

None of these

Only air

Air and fuel

14. The function of a first compression ring (top ring) is that it

Increases the combustion temperature

Creates swirl

Maintains a seal and prevents the fuel leakage

Maintains a seal and prevents escape of burned gases and loss of pressure in the combustion chamber

15. The component that connects the steering rack to the knuckles is

Pivot

Sector gear

Spline

Tie rod

16. The air resistance to a car at 20 kmph is R. The air resistance at 40 kmph will be

4R²

R

2R

4R

17. The condition that results in large quantities of HC emission is

Incomplete combustion

Low temperature combustion

High temperature combustion

High atmospheric temperature combustion

18. The instrument used to check specific gravity of acid in a battery is

Hygrometer

Hydrometer

Anemometer

Multimeter

19. The stroke of an engine is the

Volume of the cylinder

Distance between T.D.C. and B.D.C.

Internal diameter of the cylinder

Length of the connecting rod

20. The most commonly used power plant in automobiles is

Battery

I.C. engine

Gas turbine

None of these

Page 3 of 3

21. The connecting rods are generally made of __________ shaped cross-section.

I

H

C

L

22. The braking control type traction control system (TCS) generally operates in the speed range of

Less than 20 kmph

Less than 60 kmph

More than 60 kmph

Less than 40 kmph

23. If the air-fuel mixture ignites before the spark takes place at spark plug, the condition is called

Rumble

Detonation

Pre-ignition

Ignition

24. The coefficient of friction for the clutch facing is approximately

0.4

1.2

0.8

0.1

25. The engine oil viscosity is defined by ___________ ratings.

Automatic transmission fluid (ATF)

Gross vehicle weight (GVW)

American petroleum institute (API)

Society of automotive engineers (SAE)

26. The octane rating of petrol commercially available is

110-125

85-95

95-100

100-110

27. The capacity of a battery is usually expressed in terms of

Amperes

Ampere hours

Volts

Weight

28. The main feature of Macpherson strut suspension is that

Non vertical external forces are supported by the suspension arms

The unsprung mass in lighter

The assembly is slightly more complicated in design

The vertical size of the suspension can be made more compact

29. In a square type engine

Diameter and length of piston are same

Geometrical shape is square

Two cylinders are placed horizontal and two vertical

Stroke length and cylinder bore are same

30. The negative plates of a lead acid battery has

Spongy lead (Pb)

Sulphuric acid (H₂SO₄)

Lead sulphate (PbSO₄)

Lead peroxide (PbO₂)

Loading...

Share this Now with Friends:

WhatsApp
Telegram
More

Related

Tags: Automobile Engineering Mechanical Engineering

VideRime

A Demrot is the founder of VideRime Online Learning, a leading engineering website. He did his BE Civil and M.Tech Structure from RGPV University, Bhopal and has been working as an Assistant Professor in a reputed college.

Leave a ReplyCancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Ads by Google

Recent Posts

Key Benefits of Phd in any Discipline
[PDF] Basic Civil Engineering and Mechanics Available Online in PDF by S.S. Bhavikatti
Best 20 trending Topics for final year major projects in Civil Engineering
Explain different types of road bridges through neat sketches
What are the best video editing softwares
Explain the working of marshalling yard through neat diagram
Classification of Indian Railways in detail
What do you mean by coning of wheels? Also discuss its advantages.

Membership Registration

Secured Payment

Protection

DMCA.com Protection Status

VideRime.com is the leading online Learning portal. ©2026 All Rights Reserved.

Login Now

Google

OR

* Username

*

* Password

*

Remember me

Forgot Password

Don't have account? Register Now

VideRime Registration Form

* Username

*

* Username

*

* Last Name

*

* Email Address

*

* Confirm Email Address

*

* Password

*

Strength: Very Weak

(Use Cropper to set image and
use mouse scroller for zoom image.)

Already have an account? Login