Engineering Drawing MCQs Practice Set-2

May 21, 2021

Show paginator

Hide paginator

20%

Page 1 of 5

1. The offset distance for the width (front to back) distance of the auxiliary view is the same distance of the ________ in the top view.

Length

None of these

Height

Width

2. In this type of view, the cutting plane line indicates both the location of the cutting plane and the direction of sight:

Removed section

Auxiliary section

Partial section

Revolved section

3. This is a common method for connecting steel members of buildings and bridges:

Riveting

Assembly

Fabricating

Welding

4. In this type of concrete, the steel is pre-tensioned before the superimposed load is applied:

Aggregate

Preloaded

Pre-stressed

Reinforced

5. These are lines drawn on a map to locate, in the plan view, points of equal ground elevation:

Profiles

Elevations

Contours

Hatches

6. These plans, made by the steel fabricator, are assembly drawings for the steel structure

Assembly plans

Welding plans

Construction plans

Erection plans

7. This type of auxiliary view is projected onto a plane that is perpendicular to one of the principal planes of projection:

Secondary

Primary

Revolved

Successive

8. The Press-Pull tool will ________ the face of a solid model in the direction it faces.

Spiral

None of these

Taper

Extrude

9. The 3-D commands on the Modeling toolbar include __________.

All of these

Box

Sphere

Extrude

10. Perspective drawings are classified according to their number of these features:

Ground lines

Station points

Picture planes

Vanishing points

Page 2 of 5

11. A circular arc is dimensioned in the view where you see its true shape by giving the value for its

Diameter

Chord length

Radius

Arc length

12. These are vertical distances above a common datum, reference plane, or point:

Profiles

Traverse

Elevations

Plats

13. Students can complete an associate's degree in drafting which normally takes about __________ years to complete.

Two

One

Four

Three

14. These maps are used in planning installations of trees, shrubbery, drives, and other garden features:

Cadastral maps

Engineering maps

Topographic maps

Landscape maps

15. This type of surface may be a plane, a single curved surface, or a warped surface

Edge surface

Developed surface

Auxiliary surface

Ruled surface

16. This material is used in masonry construction, most commonly for ornamental facing:

Natural stone

Aggregate

Face brick

Clay tile

17. These are joined together in the field to build a structure:

Riveted members

Assembled fabrications

Main members

Steel fabrications

18. The MASSPROP shortcut will provide the following information.

Bounding box

Mass

All of these

Volume

19. Baseline dimensions are referenced from a common geometric feature known as a ________.

Datum

Corner

Edge

Point of reference

20. This type of structural steel drawing shows all dimensions necessary for fabrication:

Application drawings

Weldment drawings

Shop drawings

Design drawings

Page 3 of 5

21. In oblique projection, important shapes should be in this position relative to the viewing plane:

Rotated

Perpendicular

Parallel

Adjacent

22. The maximum and minimum sizes of a feature are identified by a ________ tolerance.

GD&T

Allowance

Limits

Reference

23. These maps are used to plan construction projects that locate construction features so they fit the topography of the area:

Structural topography maps

Subdivision plats

Structure location plans

Landscape maps

24. Oblique sections are useful to show this

Foreshortened features

Oblique lines

Projected features

Interior shapes

25. Architectural drafters generally prefer to use ________ drawings to help illustrate 3-dimensional views of a structure.

Perspective

Isometric

Auxiliary

Orthographic

26. A partial auxiliary view is used to show only the __________ in the auxiliary view.

None of these

The projected top view

The projected side view

Projected inclined plane

27. These are special installations of stone or concrete marking the locations of points accurately determined by precise surveying:

Monuments

Pillars

Topographic marks

Hatches

28. A projection weld is a type of

Arc weld

Fillet weld

Resistance weld

Gas weld

29. CAD programs which incorporate parametric modeling utilize a system in which the dimensions control the ________.

Perspective of the model

All of the above

Size and shape of the model features

Shading used to render the model

30. This type of weld is the most common in structural steel fabrication:

Beam weld

Structural weld

Fillet weld

Rivet weld

Page 4 of 5

31. This type of solid has two bases that are parallel equal polygons:

Cone

Torus

Prism

Pyramid

32. These weld symbols have no arrow-side or other-side significance:

Surface or groove weld

Projection or seam weld

Back or backing weld

Flash and upset weld

33. EDM is the acronym for:

Enterprise drawing manipulation

Enterprise data management

Engineering drawing management

Engineering data manipulation

34. A secondary auxiliary view is a projection off of the __________.

Top view

None of these

Front view

Primary auxiliary view

35. In a CAD system, you can draw an ellipse by specifying these

The center and major and minor axes

The midpoint and end points

The bounding lines

The center and radius

36. This is used in drawings to represent the edge of a solid object:

Line

Vertex

Angle

Surface

37. Circular shapes appear in this fashion when viewed at an angle other than 90 degrees:

Angular

Circular

Lengthened

Elliptical

38. The View toolbar will position the view of the 3-D solid toward the ________.

Left side

All of these

SE isometric

Front

39. This is a systematic approach that integrates the design and manufacture of products with the goal of optimizing the process

Concurrent design

Design for recycling

The manufacturing process

Traditional engineering design

40. This allows the designer to conceptualize objects more easily without having to make costly illustrations, models, or prototypes:

Computer-aided manufacturing

Computer-aided engineering

Computer-aided design

Computer-aided prototyping

Page 5 of 5

41. The Free Orbit tool is found on the ________ toolbar.

Rotate

3-D Move

Move

Modify

42. An oil refinery relies on which type of drafter to maintain and update the technical piping drawings used for the construction and maintenance of the facility.

Architectural

Civil

Electrical

Process piping

43. This is the most common application for developments and intersections:

Mechanical engineering

Sheet metal construction

Piping

Architecture

44. Switches and relays should be shown in this position with no operating force or applied energy:

Application

Offset

Closed

Normal

45. This type of drawing is created to calculate areas, locate property lines, and locate building projects and facilities:

City map

Traverse

Plat

Contour

46. One way to evenly space dimensions on a drawing is to use the __________.

Baseline tool

Linear tool

Continue tool

Dimension Space tool

47. Approximately this much of the cost of product development and manufacture is determined at the design stage

60-75 %

70-80 %

75-85 %

40-50 %

48. Technical drawings typically serve one of three purposes:

Visualization, Communication, or Documentation

Documentation, Installation, or Engineering

Visualization, Dimensioning, or Documentation

Communication, Documentation, or Installation

49. Welding drawings are a special type of this kind of drawing:

Perspective

Symbol

Assembly

Isometric

50. These are accurately drawn maps of cities and towns showing property lines and other features that control property ownership:

Topographic maps

Monument maps

Cadastral maps

City maps

Engineering Drawing MCQs Practice Set-2

Related

1 Response

Leave a ReplyCancel reply

Secured Payments

Protection

Engineering Drawing MCQs Practice Set-2

Share this Now with Friends:

Related

1 Response

Leave a ReplyCancel reply

Secured Payments

Protection